How To Troubleshoot A Scooter That Won’t Start With The Electric Starter

By | November 28, 2022

In this article, we will discuss why your scooter won’t start with the electric starter and what to do about it. A faulty ignition switch can cause your scooter to not start using the electric starter; however, there are several other issues that may be to blame as well.

The good news is that it’s usually not difficult to figure out what’s wrong and fix it, so long as you have the right tools on hand and know what to look for.

Read on to find out how to troubleshoot your scooter so you can get back on the road safely and quickly!

How do I know if my starter is bad on my scooter?

A bad starter is an absolute deal breaker for your scooter, so it’s crucial you know how to tell if yours is going bad. Here are some warning signs: if your scooter is not running at all, or if it has weak acceleration, then most likely the starter may be going bad.

How to Bypass Your Scooter’s Ignition with 5 Wires

You should also check if your starter button doesn’t work. If there is a heavy grinding noise when you try to start up your scooter (that doesn’t go away), this could mean that your bearings are worn and need replacing.

It’s also important to make sure that there isn’t excess gasoline in the carburetor – this could cause engine flooding, which will also prevent ignition.

Make sure your battery cables are tightly connected and that you have oiled the valves of your scooter before trying to turn it over again.

Troubleshooting

Check the Battery

Start by checking the battery. If the battery is low, charge it until it’s full and try starting again. If the battery is fully charged and you’re still having problems, make sure there isn’t any dirt or debris blocking the spark plug holes.

You can also check to see if you have fuel in the tank by looking at the fuel indicator window on your gas cap. If there’s no fuel, fill up and try again.

If you’re still having trouble and all of these steps have been followed, it may be time for a new battery or carburetor clean-out kit! Your best bet is taking your scooter into an authorized service center for diagnosis and repair.

Authorized service centers are trained to find the root cause of the problem quickly so they can provide the most cost-effective solution.

Check the Fuses

As the last step, before considering other possible issues with the battery or wiring, check the fuses. If you have an older scooter, there will be two fuse boxes: one under the seat and one on the left side of the handlebars.

On newer models, there is only one fuse box under the seat. Take off the cover plate and see if any fuses are blown. Remember to turn off your lights first! If any of these fuses are blown, replace them and turn your lights back on.

The new fuses should stop the circuit breaker from tripping again. Check for corrosion in the wires as well, which can cause this problem. If everything checks out and your scooter still won’t start, it may just need a jump-start from another vehicle’s battery cables.

Check the Starter Relay

The first thing you’ll want to do when your moped won’t start is check the electric starter relay. If the relay is bad, it’ll need to be replaced. If the relay checks out, try and see if the battery is dead or too low on power. If it’s not either of these, there could be an issue with ignition coil or spark plugs. These are usually easier fixes than replacing the electric starter.

Check the Starter Motor

The Starter Motor is the heart of any Electric Start Scooter. When you turn the key and press the throttle, your Starter Motor will engage and start spinning. If it’s not spinning or it’s not engaging, then your scooter won’t be starting. The following are some tips on how to troubleshoot a moped or scooter that won’t start:

1) Check for loose connections- this includes all electrical connections as well as the connection between the spark plug and wire.

2) Remove the headlight from the handlebar. Turn the key and observe if there is a spark coming from where you removed the headlight – if there isn’t then make sure that your battery is fully charged and properly connected.

3) Next, check for fuel in the tank by removing both screws at the top of your gas tank and look inside with a flashlight to see if there is fuel in your tank. If there’s no fuel in your tank, fill it up with new gas (and make sure to replace both fuel screws).

4) Your Starter Motor might be worn out – replace it!

Check for Loose Wires

If your moped won’t start, first check for loose wires. Pull out any exposed wires and make sure they are all firmly inserted into their respective plugs. If you’re using an extension cord, make sure it is securely connected to both the outlet and the scooter.

Check for any signs of damage in either of these areas too, which can prevent electrical current from flowing through. If there is no damage, move on to step two.

Next, check if the spark plug needs to be replaced. Your spark plug needs to be replaced every 6-12 months depending on use and distance ridden. To test this, disconnect the spark plug wire(s) or remove them completely.

Turn your ignition key so that it goes at least halfway around (clockwise). If there’s a lack of electricity or sparks coming from the end of the plug then it’s time for a replacement.

FAQs

Why is my electric starter not working?

Scooters are great because they’re easy to ride and it’s even easier when your scooter has an electric starter. But what if your moped or scooter won’t start with the e-starter? There are a few things you can do before giving up on your ride for good. One possibility is that your battery needs a charge.

You can check this by turning on the lights, headlight, and taillight for about 10 minutes. If these functions all work, then your battery may be at full capacity and doesn’t need a charge.

On the other hand, if none of these functions work after 10 minutes of use, then you might need to jumpstart or recharge your battery.

Where do I tap my starter to get it to start?

The first thing you’ll want to do is make sure your battery is charged. If your battery needs a charge, then you’ll need to plug it in for about 8 hours before trying again.

Next, try unplugging and replugging the connector between your battery and bike. You may also need to tap on the starter button and hold it down for 5-10 seconds until it kicks in.

What would cause a starter to not turn over?

If your battery is dead, the starter will not be able to turn over. If you don’t have a spare battery and it’s not time for recharge yet, you can use jumper cables and another vehicle to jump-start your engine. This will get your bike running enough for you to get home or into town where you can find a new battery.

Conclusion

If your moped won’t start, try these things:

-Check for loose connection or bad battery.

-Check for broken wires, or loose wiring around engine.

-Check the fuse box or breaker panel (including fuses) and make sure everything is in working order.

-Make sure your choke is not set too high or too low.

-If you’re using gas, check fuel line and make sure tank is not empty.

-If you’re using electric, check power switch on handlebar and make sure it’s on as well as charge cord plugged in properly to bike and charger outlet.

Leave a Reply

Your email address will not be published. Required fields are marked *